If it malfunctions and the electrical signals are not sent to the compressor and other parts, the compressor will not turn on. As a rule, a 1.3v for AAA-type batteries is considered dead. Adjust the thermostat temperature set point to a cooler degree by checking the room temperature and lowering the current thermostat reading a degree at a time. Using a, 3/16" drill bit, drill the holes you have marked. Cooling coils remove heat from the air in your AC. 1.5A per terminal (3A total)if(typeof ez_ad_units!='undefined'){ez_ad_units.push([[300,250],'manuals_plus-box-4','ezslot_5',164,'0','0'])};__ez_fad_position('div-gpt-ad-manuals_plus-box-4-0');Temperature Control: 45F to 90F (7C to 32C)Temperature Accuracy: 1F ( 0.5C)if(typeof ez_ad_units!='undefined'){ez_ad_units.push([[250,250],'manuals_plus-banner-1','ezslot_6',165,'0','0'])};__ez_fad_position('div-gpt-ad-manuals_plus-banner-1-0');Safety InformationThis thermostat is for LOW voltage applications only.Turn OFF electricity to all heating and cooling components.if(typeof ez_ad_units!='undefined'){ez_ad_units.push([[300,250],'manuals_plus-large-leaderboard-2','ezslot_7',166,'0','0'])};__ez_fad_position('div-gpt-ad-manuals_plus-large-leaderboard-2-0');All wiring must conform to applicable local and national building and electrical codes and ordinances.Included in PackageThermostatif(typeof ez_ad_units!='undefined'){ez_ad_units.push([[300,250],'manuals_plus-leader-1','ezslot_8',167,'0','0'])};__ez_fad_position('div-gpt-ad-manuals_plus-leader-1-0');J-Box mounting plate/ decorative trim plateJ-box mounting screwsDry wall anchors and mounting screwsWiring labelsGL to GH Jumper wireInstalling the ThermostatIf painting or construction is still ongoing, cover the thermostat completely or wait until work is complete before mounting thermostat.if(typeof ez_ad_units!='undefined'){ez_ad_units.push([[250,250],'manuals_plus-large-mobile-banner-2','ezslot_10',170,'0','0'])};__ez_fad_position('div-gpt-ad-manuals_plus-large-mobile-banner-2-0');Mount the thermostat on an inside wall about five feet above the floor in an area that has good circulation but is not directly affected by a vent or duct.Ensure power is switched OFF at the PTAC unitMounting directly on the wallUse a flat head screw driver to separate the front and back housing of the thermostatif(typeof ez_ad_units!='undefined'){ez_ad_units.push([[250,250],'manuals_plus-leader-2','ezslot_11',172,'0','0'])};__ez_fad_position('div-gpt-ad-manuals_plus-leader-2-0');If new mounting holes are needed, mark the placement of the new mounting holes through the thermostat base. 4 0 obj Using a 3/16 drill bit, drill the holes you have marked and insert the supplied wall anchors.if(typeof ez_ad_units!='undefined'){ez_ad_units.push([[300,250],'manuals_plus-leader-3','ezslot_12',174,'0','0'])};__ez_fad_position('div-gpt-ad-manuals_plus-leader-3-0');Feed the wires through the hole in the trim plate and screw the trim plate to the wallif(typeof ez_ad_units!='undefined'){ez_ad_units.push([[250,250],'manuals_plus-large-mobile-banner-1','ezslot_9',703,'0','0'])};__ez_fad_position('div-gpt-ad-manuals_plus-large-mobile-banner-1-0');Use a flat head screw driver to separate the front and back housing of the thermostatFeed the wires through the back housing of the thermostat and then snap the back housing to the trim plateYour thermostat base should now be securely fixed to the wallMounting on Junction BoxInstall junction boxFeed the wires through the hole in the trim plate and hang the trim plate on the top screwInsert mounting screw into top of junction box until there is approximately 1/8 gap between the screw head and the wall Use a flat head screw driver to separate the front and back housing of the thermostatFeed the wires through the back housing of the thermostat and then snap the back housing to the trim plateYour thermostat base should now be securely fixed to the wallUsing the WIRING DIAGRAMS section, wire each terminal on the thermostat base. If that is not the case, it will feel like the heat is not working. Lift the filter from the center part so that the locking hood is unfastened and pull the filter towards you to take it out. If your Friedrich air conditioners heat is not working, the thermostat is set on the wrong Mode or the AC is wrong-sized for the heat requirements of the space being heated. Every time your Friedrich AC runs, it has received a signal from the thermostat that the temperature in the room is above the set level and its time to run the next cooling cycle. Youll receive an email or phone call with repair quotes from each service. Follow these steps to clean your dirty or clogged Friedrich AC air filter: Note: If your Friedrich AC filter is worn out or damaged, replace it immediately. The Friedrich electric heat models which are air conditioners with a built-in space heater.
Harris County Voting Locations By Zip Code,
Housing Portal Cu Boulder,
Articles F